High Capacity All Weather Electronic Ignition System

AWEIS High Capacity Electronic Ignition System

Price in points: 136680 points
Add to Wishlist


This AWEIS (All Weather Electronic Ignition System) is our high capacity version that is made for lighting a large fire pit or fire feature. This AWEIS is custom made to provide easy electronic starting of your burner ring. Add the smart phone module and you can use this in conjunction with our app to light your fire pit remotely! The best part about our high capacity AWEIS is that we have the product knowledge to help you make sure it is proper for your specific application. Don't forget to give us a call if you need help finding other outdoor fire accessories. Get this ignition system for your fire feature from the number one contractors' source for DIY fire pits. We are your outdoor fire experts that love to help start a custom backyard blaze!

  • Meets ANSI Z21.97-2014
  • CSA 2.41-2014
  • CSA C22.2 No. 3-M1998 (R2014)
Features & Benefits:
  • 12" heat sheild
  • Works in fire bowls or gas fire pits. No need to light your fire with a match or lighter - the High Capacity AWEIS does all the work!
  • Automatic start on the High Capacity AWEIS enables it to restart your fire quickly during rain or a mild breeze. 

It truly does work in all weather conditions, see for yourself!

BTU: Up to 512,000 Max
Voltage: 24 Volts AC
Height: 5 Inches
Width: 4 1/2 Inches
Length: 4 1/2 Inches
Ignition Type: Hot Surface Ignition (Glow Plug)
Ignition Source: Pilot
Ignition Sequence: Intermittent Pilot
Inlet/Outlet Size: 1/2 Inch FPT
PSI Required: 2 PSI

Estimated Lead Time

Ships out within 10-15 days.

Warranty Information

Manufacturer's Warranty:

All electronic ignition systems are warranted for (1) year with a limited warranty for (2) years. As part of the one year warranty, in the event a system has to be replaced due to a defect/malfunction of the system, manufacturer will replace the system free of charge. This warranty does not cover labor costs. Problems in the functioning of the systems due to gas plumbing or electrical installed by others are not covered under this warranty. In the event a system fails after the first year (from date of purchase) and within two years of date of purchase, the cost for a replacement system is at a discount rate of 50% of the current listed price. Manufacturer is not responsible for the cost of labor incurred for replacing a system purchased at the discounted rate.



** Be sure to have a qualified installer check the following **

Issue: When I turn on the Ignition System nothing happened?

Check: When this happens it is usually due to an electrical wiring or power issue. Make sure to properly check all your electrical connections to ensure that all wires connecting to the transformer as well as the fire feature are connected properly. If all wires appear to be connected, disconnect the wires at the fire feature and attach a Multimeter to the wires to confirm a minimum of 24 volts when the fire feature is turned on. If you do not have a minimum of 24 volts conduct the same test at the transformer to ensure the transformer is in fact producing a minimum of 24 volts. If you do have a minimum of 24 volts at the fire feature E-Mail us the following at [email protected]:

  • Your name
  • Order# if you have it
  • Short video of how your fire feature is working
  • Few photos showing the set up of your system.
    • If you have media in/on feature please take photo with media
    • If no media just the set up will do

Issue: After I installed the Electronic Ignition System I turned it on, I can see the glow plug is glowing and I can hear the gas flowing but no fire?

Check:  This may be caused by a couple of issues.

  1. Air in the gas lines

If a new gas line was installed and the air was never purged from the lines prior to installing the electronic ignition system then it may take a few times of turning the fire feature on and off before the air is out of the lines. Here is how our Electronic Ignition Systems work:  after you turn it on the glow plug will come on first followed by the Pilot Gas Valve opening 4 seconds later. For the next 3 minutes the glow plug will cycle on and off every 30 seconds while the Pilot Gas Valve will remain on the entire time. Therefore if you are attempting to purge air from the gas line, turn the system on and leave it on for approximately 3 minutes. Then turn it off and then back on (no need to wait to turn it back on). Let the system run for another 3 minutes. Usually when purging air from a new gas line you will need to cycle the power several times as described above before gas begins to flow. If at any point you smell gas but still don't have ignition, attempt to light the Pilot flame with a handheld lighter. If the flame ignites when you light it by hand please see information under "Electrical Current".

      2. Electrical Current

If you have checked your gas lines and believe that there is no air in the lines, then most likely the failure to ignite the fire feature is due to the fact the glow plug may not be getting hot enough to ignite the gas. The reasoning as to why a glow plug may not be getting hot enough is is that it is most likely not getting enough 'amps'. The number of amps reaching the fire feature is heavily dependent on the gauge wire used between the transformer and the fire feature. Our Install Instructions require no less than 12 gauge wire be run for all fire features. Often times we learn that in many cases less than 12 gauge wire has been used and herein lies the cause of the problem. 

Here is how to determine if there are enough 'amps' getting to your fire feature.

  1. CAUTION: Turn off the gas supply prior to the next step.
  2. Using a clamp on ammeter, clamp the ammeter around one of the wires providing power to the Electronic Ignition System.
  3. Turn the fire feature on.
  4. The amps you should see will range between 1.4 to 1.6 amps initially. Four seconds after being turned on the amps will jump to approximately 2.0 amps.

If you do not see the amps listed above AND the wire gauge used was less than 12 gauge wire – change the wiring. Otherwise contact us for further assistance at the e-mail listed above.

Issue: I turned my fire feature off, so why can I still see small flames coming from my fire feature?

Check: Turn your fire feature on and let the main fire ring light, then turn it off again, you will want to do this multiple times. Small pieces of debris from the  gas line can sometimes get caught in the main or pilot valve which may cause it from closing all the way. This will happen sometimes with a new gas line, and by cycling the power often times this will dislodge the debris. If cycling the power does not work for you and does not solve the issue, turn the gas off using the manual shutoff and contact us at the e-mail provided above for further assistance.

Product Question

Please feel free to contact us if you have any questions or need more information about this product using the New Question tab. Please ONLY SUBMIT product questions. For all other questions go to contact us,


No posts found

Write a review
Last updated on December 5th 2017.

Subscribe To Our Newsletter

Get the latest news, reviews, and deals in your email!